Minimserver is not working

[masanorikado]

I installed MinimServer 2.1 using manual install on my QNAP NAS a few days ago.
I was using MinimServer without any problems until yesterday.
MinimServer is not working today after I updated it by auto-update.
The icon of MinimWatch on my Windows is grey.
I have attached log files on my QNAP NAS.
Is it related to the deletion of JRE_ARM?
What should I do?

[RSJ]

(23-12-2021 15:58)masanorikado Wrote:  I installed MinimServer 2.1 using manual install on my QNAP NAS a few days ago.
I was using MinimServer without any problems until yesterday.
MinimServer is not working today after I updated it by auto-update.
The icon of MinimWatch on my Windows is grey.
I have attached log files on my QNAP NAS.
Is it related to the deletion of JRE_ARM?
What should I do?

I am pretty sure that JRE does need to be installed on the QNAP.

[masanorikado]

(23-12-2021 16:19)RSJ Wrote:  

(23-12-2021 15:58)masanorikado Wrote:  I installed MinimServer 2.1 using manual install on my QNAP NAS a few days ago.
I was using MinimServer without any problems until yesterday.
MinimServer is not working today after I updated it by auto-update.
The icon of MinimWatch on my Windows is grey.
I have attached log files on my QNAP NAS.
Is it related to the deletion of JRE_ARM?
What should I do?

I am pretty sure that JRE does need to be installed on the QNAP.

Thank you for your reply.
The manual says that JRE_ARM is not needed, so I left JRE, but removed JRE_ARM.

[simoncn]

Which QNAP NAS is it? If it is TS-109, TS-209 or TS-409, JRE_ARM is required (see this page). For all other models, JRE_ARM should be removed.

[masanorikado]

(23-12-2021 18:36)simoncn Wrote:  Which QNAP NAS is it? If it is TS-109, TS-209 or TS-409, JRE_ARM is required (see this page). For all other models, JRE_ARM should be removed.

Thank you for your advise. My QNAP NAS is TS-119P II.
Installation of JRE_ARM went well, but installation of NPTL was rejected by QNAP.
In that situation, MinimServer is now working fine.
Is this all right?

[simoncn]

NPTL is for the TS-109, TS-209 and TS-409 only. It should not be used on any other model.

On the TS-119P II, you should have JRE but not JRE_ARM.

[masanorikado]

(24-12-2021 16:09)simoncn Wrote:  NPTL is for the TS-109, TS-209 and TS-409 only. It should not be used on any other model.

On the TS-119P II, you should have JRE but not JRE_ARM.

If I leave JRE and remove JRE_ARM, MinimServer does not start.
If I leave both JRE_ARM and JRE installed, MinimServer works fine.
I don't know what's going on, but I'll use it in this state.

[simoncn]

This would happen if the JRE package is not enabled. The JRE icon needs to be orange, not grey. See step 4 in this section.

[masanorikado]

(27-12-2021 18:52)simoncn Wrote:  This would happen if the JRE package is not enabled. The JRE icon needs to be orange, not grey. See step 4 in this section.

I tried deleting JRE_ARM. You were right, there was no problem.
I am sorry for making such a fuss.
Thank you for your support. I love MinimServer.