MinimServer Forum

Full Version: Minimserver is not working
You're currently viewing a stripped down version of our content. View the full version with proper formatting.
I installed MinimServer 2.1 using manual install on my QNAP NAS a few days ago.
I was using MinimServer without any problems until yesterday.
MinimServer is not working today after I updated it by auto-update.
The icon of MinimWatch on my Windows is grey.
I have attached log files on my QNAP NAS.
Is it related to the deletion of JRE_ARM?
What should I do?
(23-12-2021 15:58)masanorikado Wrote: [ -> ]I installed MinimServer 2.1 using manual install on my QNAP NAS a few days ago.
I was using MinimServer without any problems until yesterday.
MinimServer is not working today after I updated it by auto-update.
The icon of MinimWatch on my Windows is grey.
I have attached log files on my QNAP NAS.
Is it related to the deletion of JRE_ARM?
What should I do?

I am pretty sure that JRE does need to be installed on the QNAP.
(23-12-2021 16:19)RSJ Wrote: [ -> ]
(23-12-2021 15:58)masanorikado Wrote: [ -> ]I installed MinimServer 2.1 using manual install on my QNAP NAS a few days ago.
I was using MinimServer without any problems until yesterday.
MinimServer is not working today after I updated it by auto-update.
The icon of MinimWatch on my Windows is grey.
I have attached log files on my QNAP NAS.
Is it related to the deletion of JRE_ARM?
What should I do?

I am pretty sure that JRE does need to be installed on the QNAP.

Thank you for your reply.
The manual says that JRE_ARM is not needed, so I left JRE, but removed JRE_ARM.
Which QNAP NAS is it? If it is TS-109, TS-209 or TS-409, JRE_ARM is required (see this page). For all other models, JRE_ARM should be removed.
(23-12-2021 18:36)simoncn Wrote: [ -> ]Which QNAP NAS is it? If it is TS-109, TS-209 or TS-409, JRE_ARM is required (see this page). For all other models, JRE_ARM should be removed.

Thank you for your advise. My QNAP NAS is TS-119P II.
Installation of JRE_ARM went well, but installation of NPTL was rejected by QNAP.
In that situation, MinimServer is now working fine.
Is this all right?
NPTL is for the TS-109, TS-209 and TS-409 only. It should not be used on any other model.

On the TS-119P II, you should have JRE but not JRE_ARM.
(24-12-2021 16:09)simoncn Wrote: [ -> ]NPTL is for the TS-109, TS-209 and TS-409 only. It should not be used on any other model.

On the TS-119P II, you should have JRE but not JRE_ARM.

If I leave JRE and remove JRE_ARM, MinimServer does not start.
If I leave both JRE_ARM and JRE installed, MinimServer works fine.
I don't know what's going on, but I'll use it in this state.
This would happen if the JRE package is not enabled. The JRE icon needs to be orange, not grey. See step 4 in this section.
(27-12-2021 18:52)simoncn Wrote: [ -> ]This would happen if the JRE package is not enabled. The JRE icon needs to be orange, not grey. See step 4 in this section.

I tried deleting JRE_ARM. You were right, there was no problem.
I am sorry for making such a fuss.
Thank you for your support. I love MinimServer.
Reference URL's